The pace uses manual XDL into driver

  • Time:
  • Click:129
  • source:DELENO CNC Machining
XDL-15 is to use the United States new-style bipolar technology of drive of wave of constant current behead, suit drive the pace enters any two-phase or 4 photographs Composite electric machinery. Because driver interior uses special control technology, at the same time the function of frequency of on any account of electric machinery of give attention to two or morethings (high frequency when, electric machinery runs the moment of force below condition to raise 20% above in high speed; When low frequency, electric machinery runs condition to fall in low speed, noise decreases, smooth sex increases) . Its fractionize function makes the pace rises greatly into the precision of electric machinery, older rate and power can be outputted than other drive means when using same electric machinery. Its whole function is in lead position in home. 1.

Characteristic: L is high-powered, low when price L is dormant, coil is decreased shed automatic halve. Compatible L only power source inputs TTL of signal of L input report DC12V-DC40Vl precision is optional 2.

4.

8.

16.

32.

Electric current of drive of 64 fractionize L can be amounted to 1.

TTL of signal of report of input of 5A/ photograph L is compatible L4 line, 6 lines, it is OK that pace of 8 lines two-phase enters electric machinery drive 2.

Use range: This driver is in medium or small wide application receives in automation equipment and instrument. For example: Small-sized engraving tool, take put unit, pneumatic makes mark machine, laser makes mark machine, cut word engine, stick sign chance, plotter, numerical control machine tool, embroider machine. Especially user expectation high accuracy, high speed is spent, low shake, in the equipment of small impurities dispatch particularly useful. 3. Driver wiring: 4.

Cite crural definition: P1P2 brings crural date signal to bring 1PUL 1GND2DIR 2V+3OPTO 3A+4ENA 4p; 4A- 5B+ 6B-5 of crural date signal.

Bring a foot to define: (1) port of wiring of P1 weak report cites signal of pulse of 1PUL of function of crural date signal: Ascendant edge is effective. Every time pulse by low make a move of the electric machinery when becoming tall. 2DIR direction signal: Use at changing electric machinery to change direction, 4ENA of power source of drive of smooth lotus root of 3OPTO of TTL n drive makes can signal: Dormant or allow driver job low n to prohibit (2) port of wiring of P2 strong report makes land of direct current source of 1GND of function of crural date signal. Anode of 2+V direct current source. Typical cost is 24V3, photograph of A of 4A+A- electric machinery 5, 　 of 　 of 　 of photograph of B of 6B+B- electric machinery 6.

Set fractionize and electric current: This driver uses set of 6 switch that dial a code, its fractionize precision, dynamic electric current, static electric current by in-house automata, be as follows in detail: Electric current of SW1SW2SW3SW4SW5SW6 static state: After pulse stops 1 second electric current decreases the 1/2 trends that is dynamic electric current automatically voltaic fractionize precision (1) the set of fractionize precision: By 4 what open the switch that dial a code.

5.

6 decide the set of electric current of fractionize multiple SW4SW5SW61onOnon2offonon4onoffon8offoffon16ononoff32offonoff64onoffoff(2) : 1 of the switch that dial a code.

2.

Electric current of 3 set trends if: Electric current is worth SW1SW2SW30.

20Aoffonon0.

42Aonoffon0.

62Aoffoffon0.

84Aononoff1.

05Aoffonoff1.

25Aonoffoff1.

5Aoffoffoff(3) integrated citing: Some electric machinery needs the setting of XDL-15 driver to be as follows: Pace of fractionize precision =3200 / circle (16 fractionize) =0 of dynamic electric current.

84A, =0 of static electric current.

　 of 　 of 　 of 　 of 　 of 　 of On of 　 of 　 of 　 of 　 of 4A Off 　 1234567.

Power source furnishs: Power source voltage can work normally between DC40V of DC12V ─ ─ , this driver had better use power supply of blame stabilized voltage direct current source, voltage wave peak value does not exceed 40V, if exceed driver of 40V possible attaint. At the same time proposal user is used + 24V-36V dc power supply, avoid wave motion of electrified wire netting to exceed range of driver voltage job. Ask an attention: 1.

Should notice power source is being lost when wiring do not receive;2 instead.

When power supply of electrified wire netting is fluctuant, power source voltage must not exceed 40V;3.

Power supply of power source of switch of use stabilized voltage, its output voltaic limits to need to be set into maximum; 4.

Use when be not regulated power supply, 50% what source current outputs ability to should be more than driver to set next electric current; 8. The pace enters electric machinery wiring: The pace connects into electric machinery A 3 at P2 mouth.

Between 4 feet, b is conterminous 5 at P2 mouth.

Between 6 feet; It is 4 lines below, 6 lines, what 8 lines pace enters electric machinery is detailed receive a standard: 9.

Jump function of line JP1 JP2 explains: Can achieve to make driver is below different electric machinery and different pulse frequency optimal cooperate, to improve the performance of driver, ad hoc jumps line JP1 JP2, they have electrify money to alter ability only effective, its job mode expresses as follows: Pulse of 1onon of mode JP1JP2 function inputs frequency under 1000HZ when, choose pulse of 2onoff of this kind of mode to input frequency to be more than 1000HZ under 2000HZ when, choose pulse of 3offOn of this kind of mode to input frequency to be more than 2000HZ under 5000HZ when, choose pulse of 4offoff of this kind of mode to input frequency to be more than 5000HZ under 100KHZ when, choose this kind of mode to note: ON expresses to jump the line connects, OFF expresses to jump the line disconnects when need is changed, open lid, choose different pattern according to his circumstance, in order to make driver achieves optimal result. 10.

Electric and characteristic: Limits of XDL-15 power supply + 12V-40VDC peak value exports electricity 0.

1A-1.

5A (adjustable) voltage of typical power supply + 24VDC fractionize precision 2 fractionize (400 paces / circle) 4 fractionize (800 paces / circle) 16 fractionize (3200 paces / circle) 64 fractionize (12800 paces / circle) 11. Does use environment reach parameter: ? Cong is beaten wring rank divide evenly shine Qiu of Cong Chinese toon fears tasting Hui? to use environmental temperature ─ of 0 ℃ ─ + 50 ℃ humidity 90 ％ RH shakes 40 ─ ─ 6.

0m/s2 Max circumstance avoids dust, oily mist and caustic gas to save temperature as far as possible - ─ of 20 ℃ ─ + 65 ℃ weight makes an appointment with 200 grams 12.

Machinery installs measure: L=92mm W=62mm H=28mm CNC Milling